A trampoline is a small piece of code that is created at run time when the address of a nested function is taken. It normally resides on the stack, in the stack frame of the containing function. These macros tell GCC how to generate code to allocate and initialize a trampoline.
The instructions in the trampoline must do two things: load a constant address into the static chain register, and jump to the real address of the nested function. On CISC machines such as the m68k, this requires two instructions, a move immediate and a jump. Then the two addresses exist in the trampoline as word-long immediate operands. On RISC machines, it is often necessary to load each address into a register in two parts. Then pieces of each address form separate immediate operands.
The code generated to initialize the trampoline must store the variable parts—the static chain value and the function address—into the immediate operands of the instructions. On a CISC machine, this is simply a matter of copying each address to a memory reference at the proper offset from the start of the trampoline. On a RISC machine, it may be necessary to take out pieces of the address and store them separately.
A C statement to output, on the stream file, assembler code for a block of data that contains the constant parts of a trampoline. This code should not include a label—the label is taken care of automatically.
If you do not define this macro, it means no template is needed for the target. Do not define this macro on systems where the block move code to copy the trampoline into place would be larger than the code to generate it on the spot.
Return the section into which the trampoline template is to be placed (see Sections). The default value is
readonly_data_section.
Alignment required for trampolines, in bits.
If you don't define this macro, the value of
BIGGEST_ALIGNMENTis used for aligning trampolines.
A C statement to initialize the variable parts of a trampoline. addr is an RTX for the address of the trampoline; fnaddr is an RTX for the address of the nested function; static_chain is an RTX for the static chain value that should be passed to the function when it is called.
A C statement that should perform any machine-specific adjustment in the address of the trampoline. Its argument contains the address that was passed to
INITIALIZE_TRAMPOLINE. In case the address to be used for a function call should be different from the address in which the template was stored, the different address should be assigned to addr. If this macro is not defined, addr will be used for function calls.If this macro is not defined, by default the trampoline is allocated as a stack slot. This default is right for most machines. The exceptions are machines where it is impossible to execute instructions in the stack area. On such machines, you may have to implement a separate stack, using this macro in conjunction with
TARGET_ASM_FUNCTION_PROLOGUEandTARGET_ASM_FUNCTION_EPILOGUE.fp points to a data structure, a
struct function, which describes the compilation status of the immediate containing function of the function which the trampoline is for. The stack slot for the trampoline is in the stack frame of this containing function. Other allocation strategies probably must do something analogous with this information.
Implementing trampolines is difficult on many machines because they have separate instruction and data caches. Writing into a stack location fails to clear the memory in the instruction cache, so when the program jumps to that location, it executes the old contents.
Here are two possible solutions. One is to clear the relevant parts of the instruction cache whenever a trampoline is set up. The other is to make all trampolines identical, by having them jump to a standard subroutine. The former technique makes trampoline execution faster; the latter makes initialization faster.
To clear the instruction cache when a trampoline is initialized, define the following macro.
If defined, expands to a C expression clearing the instruction cache in the specified interval. The definition of this macro would typically be a series of
asmstatements. Both beg and end are both pointer expressions.
The operating system may also require the stack to be made executable before calling the trampoline. To implement this requirement, define the following macro.
Define this macro if certain operations must be performed before executing code located on the stack. The macro should expand to a series of C file-scope constructs (e.g. functions) and provide a unique entry point named
__enable_execute_stack. The target is responsible for emitting calls to the entry point in the code, for example from theINITIALIZE_TRAMPOLINEmacro.
To use a standard subroutine, define the following macro. In addition, you must make sure that the instructions in a trampoline fill an entire cache line with identical instructions, or else ensure that the beginning of the trampoline code is always aligned at the same point in its cache line. Look in m68k.h as a guide.
Define this macro if trampolines need a special subroutine to do their work. The macro should expand to a series of
asmstatements which will be compiled with GCC. They go in a library function named__transfer_from_trampoline.If you need to avoid executing the ordinary prologue code of a compiled C function when you jump to the subroutine, you can do so by placing a special label of your own in the assembler code. Use one
asmstatement to generate an assembler label, and another to make the label global. Then trampolines can use that label to jump directly to your special assembler code.